Company
LED Multifunction Power Meter Analyzer MPM8000S with RS485
Product specification
MPM8000S is a powerful multifunction power meter with modular design, which can be applied for monitoring and controlling of the electrical system. MPM8000S can measure and analyze power parameters, such as U, I, In,F, S, P, Q, PF, kWh, kvarh etc. MPM8000S has the following functions: RS-485 communication port (MODBUS Protocol),Max/min data record, analog output, digital signal input, and multi- tariff function etc.
Product specification
MPM8000S is a powerful multifunction power meter with modular design, which can be applied for monitoring and controlling of the electrical system. MPM8000S can measure and analyze power parameters, such as U, I, In,F, S, P, Q, PF, kWh, kvarh etc. MPM8000S has the following functions: RS-485 communication port (MODBUS Protocol),Max/min data record, analog output, digital signal input, and multi- tariff function etc.
All our instruments fulfill all
Measured scope
The meter can be applied in secondary measure in high and low voltage electrical system.The measured data can be communication transmitted.It can achieve the function of meansureing and anylzing parameters for single phase, 3-Ph 3wire and 3-Ph 4Wire system (include unbalance load).
Technical Specification
Input Current
Current input:5A
Measured scope:0.5%~120% In
Overload: 2 X rated continuously, 100A/1s non continuously
Measured power consumption: less than 0.2 VA per phase
Voltage Input
Voltgae input:400VAC(phase voltage),693VAC(wire voltage)
Allowed frequency scope: 45~65Hz
Measurement Scope:3%~120%
Overload: 2 X rated continuously, 2500V/1s non continuously
Power consumption: less than 0.5VA per phase
Remote input(optional)
input channel: 1channel
input mode: Dry contact
Analog output(optional)
Output channel: 1 channel programmble
output signal: 4~20mA or 0~5V(optional)
Response time: less than400ms
Output wave: less than18mV(sharp-sharp value)
load capitity: less than500OHM(4~20mA)or ≥250OHM(0~5V)
Pulse output(standard)
No. of outputs: 2 channels (active/reactive energy each without power)
Output type: Reactive pulse output
Pulse Energy Constant: 1 ~ 9600
Pulse width: (20 ~ 100) ms
Serial com. port(optional)
NO. of outputs: 1 RS-485 port
Communication protocol: Modbus-RTU protocol
Baud rate: 2400, 4800, 9600, 19200, 38400 bps
Multi-tariff rate (optional)
No. of time phase: 2 - 12 phase
Alternate time: a multiply of 30 minutes
Multi-tariff type: sharp, peak, flat, valley
Time pahse: 2 - 12 phase
Other parameters
Auxiliary power: 85~265VAC/DC (30VDC is optional; 23 is “+” terminal and 24 is “-” terminal when use DC.)
Display type: LED display
Operation type: Key or software operation
Temp. Drifting factor: <100PPM/ celsius degree
Withstand Voltage (Input against input): 2500V/1 min
Withstand Voltage (Input against output): 2500V/1 min
Withstand Voltage (Remote input against output): 1500V/1 min
Total power consumption: <5VA
Operation temperature: -20~60 celsius degree
Storage temperature: -40~85 celsius degree
Operation humidity: 5~95%RH
Pollution Class: Class 2
Material of Housing: Flammability acc. to UL94V0
Protection Class Temp.: IP 30
Dimensional Size: 96 mm x 96 mm x 78mm
Installation size: 91 x 91mm
